當前位置：上海榮計達儀器科技有限公司>>公路土工試驗儀器>>手動鋪砂儀

手動鋪砂儀

返回列表頁

參考價

面議

具體成交價以合同協議為準

產品型號PS-1

品牌

廠商性質其他

所在地上海市

在線詢價收藏產品查看聯系電話

紡織服裝機械網采購部電話：0571-88918531QQ:2568841715

聯系方式：查看聯系方式

更新時間：2024-02-14 15:44:16瀏覽次數：141次

聯系我時，請告知來自紡織服裝機械網

產品分類 品牌分類

  公路土工試驗儀器

全部產品列表

暫無信息

上海榮計達儀器科技有限公司

經營模式：其他

商鋪產品：1006條

所在地區：

聯系人：王林

詢價 給他留言

產品簡介

手動鋪砂儀,公路土工試驗儀器

詳細介紹

手動鋪砂儀適用于測得路面宏觀粗糙度,路面構造深度是表征路面粗糙度的一項指標。

The pavement depth gauge is suitable for measuring the macro roughness of the pavement. The pavement depth is an indicator of the pavement roughness.

手動鋪砂儀校驗項目

★標定構造深度尺尺寸。

★測量推平板直徑，目測底面是否粘一層1.5mm的橡膠片。

★校驗砂量筒容積。

Pavement structure depth gauge, manual sanding instrument calibration project
★ Calibration structure depth gauge size.
★ Measure the diameter of the push plate and visually check whether the bottom surface is stuck with a 1.5mm rubber sheet.
★ Verify the volume of the sａnd cylinder.

手動鋪砂儀結構組成：

★量筒，體積為25±0.15毫米

★攤鋪板。下面貼一塊2-4毫米橡膠板

★擋風板

★構造深度尺

★外形尺寸：50X180X80mm

★重量：1.76kg

Pavement structure depth gauge, manual sanding device structure:
★ Measuring cylinder, the volume is 25±0.15 mm
★ Paving board. Attach a 2-4 mm rubber sheet below
★ windshield
★Structure depth gauge
★Dimensions: 50X180X80mm
★ Weight: 1.76kg

手動鋪砂儀使用說明：

★將路面松散顆粒及浮土擦凈。

★用儲砂瓶將量筒注滿干砂，再用攤鋪版邊緣輕輕敲打量筒三下，加滿干砂，刮去高出之干砂。

★將干砂倒在路面上，用攤鋪板細心地將砂子在路面上作圓周動作攤鋪開，盡可能攤鋪成圓形。

★用構造深度尺分別通過砂面圓心，并互相垂直量取兩個構造深度值，取平均值代表該路面這一點的構造深度。

★在同一路段上作5點測定，每點相距3-5米，測點盡可能選在車轍帶上，距路面邊緣不小于1米，取5點的平均值作為該路段的構造深度。

Pavement construction depth gauge, manual sanding instrument instructions:
★ Wipe the loose particles and floating soil on the road surface.
★ Fill the cylinder with dry sａnd with a sａnd storage bottle, then gently tap the measuring cylinder with the edge of the paving plate, fill it with dry sand, and scrape off the dry sand.
★ Pour the dry sａnd on the road surface, carefully spread the sａnd on the road surface with the paving board, and spread it as round as possible.
★ Use the construction depth ruler to pass through the center of the sａnd surface, and measure the two construction depth values perpendicularly to each other. The average value represents the construction depth of the road surface.
★ Make 5 points on the same road section. Each point is 3-5 meters apart. The measuring point should be selected on the rut belt as much as possible. It is not less than 1 meter away from the edge of the road. The average value of 5 points is taken as the construction depth of the road section.