路面材料強度試驗儀是一種多功能的公路路基材料實驗儀器，它由底座、變速箱、立柱、支架、電機、電器開關等組合而成。
The pavement material strength tester is a multifunctional roadbed material tester. It is composed of a base, a gearbox, a column, a bracket, a motor, and an electrical switch.
路面材料強度試驗儀主要特點：
■采用**的計算機技術與高精度的傳感器技術相結合。
■設有過載保護，下降過位保護。
■操作簡便，測試數據準確，性能穩定可靠。
■儀器手動試驗，顯示試試件變形時的瞬時壓力及A大壓力。
■可存儲15組試件的試驗結果。
■數字顯示壓力。
■可以做抗壓和石灰土劈裂試驗。
■有快速和慢速兩種速度。
■可以選配備微型打印機。
Main characteristics of pavement material strength tester:
■ Combining computer technology with high-precision sensor technology.
■ With overload protection and falling over-position protection.
■ Easy operation, accurate test data, stable and reliable performance.
■ Manual test of the instrument, showing the instantaneous pressure and large A pressure when the test piece is deformed.
■ Can store the test results of 15 groups of test pieces.
■ Digital display pressure.
■ Can do compression and lime soil split test.
■ There are two speeds, fast and slow.
■ Optional micro printer.
路面材料強度試驗儀技術參數：
■ A大額定載荷：99.99Kn
■ 絲桿A大移動距離：200mm
■ 機動速度: 快速50mm/min
慢速1m/min
■ 手動速度：0.2mm/搖把每圈
■電機規格：550w 380v1400p/min
■重量：120KG
■ 外形尺寸：600x600x1450mm
■電源電壓：380V
■功率：800W
■環境溫度： ≤35℃。
■相對濕度： ≤85%
Technical parameters of pavement material strength tester:
■ A large rated load: 99.99Kn
■ Large moving distance of screw rod A: 200mm
■ Maneuvering speed: fast 50mm / min
Slow 1m / min
■ Manual speed: 0.2mm / revolver
■ Motor specifications: 550w 380v1400p / min
■ Weight: 120KG
■ Dimensions: 600x600x1450mm
■ Power supply voltage: 380V
■ Power: 800W
■ Ambient temperature: ≤35 ℃.
■ Relative humidity: ≤85%
路面材料強度試驗儀結構原理：
該儀器由底座、減速箱、立柱、橫梁及罩殼等組成。
電動機及控制電器置于底座內，減速箱置于底座上。
橫梁、減速箱及底座經兩根立柱相聯接，橫梁并可上下調節，以適應不同高度的試樣，橫梁下平面可聯接測力環。
底座及減速箱外面裝有罩殼。
試驗儀加載有兩種形式，一種是電動，電動機由同步齒形帶傳遞給減速箱，經減速箱減速后，旋轉運動轉換成絲桿的垂直運動，從而達到對試樣垂直加載的功用。另一種是手動，將調速手柄置于空檔，即可用搖手柄進行手動加載。
Structural principle of pavement material strength tester:
The instrument consists of a base, a reduction box, a column, a beam and a cover.
The motor and control electronics are placed in the base, and the reduction box is placed on the base.
The beam, the reduction box and the base are connected by two upright columns. The beam can be adjusted up and down to accommodate samples of different heights. The lower plane of the beam can be connected with a force measuring ring.
A cover is installed on the base and the reduction box.
The tester is loaded in two forms. One is electric. The motor is transmitted to the reduction gear by a synchronous toothed belt. After the reduction gear is decelerated, the rotation movement is converted into the vertical movement of the screw, so as to achieve the function of vertical loading of the sample. The other is manual. Put the speed control handle in neutral position, and you can use the rocker handle for manual loading.
路面材料強度試驗儀注意事項：
1.路面材料強度試驗儀的絲桿盤上升的**限位置為其盤面距基座箱體頂面300mm；絲桿盤下降的**限位置為其盤面距基座箱體頂面60mm，如果超過以上兩個**限，路面材料強度試驗儀有可能會損壞。
2.試驗儀應該安放在一個地面應平坦、穩固的位置，而且試驗儀應有接地安全防護裝置。
3.應注意經常對路面材料強度試驗儀進行維護保養：
①.應經常保持路面材料強度試驗儀的干凈整潔，每次使用完后須清掃臺面及周圍環境并擦拭干凈。
②.絲桿及盤子，立柱擦拭干凈后應涂上防銹油，并每天使用前應向絲桿滴注適量的潤滑油（20號機油）。以保證絲桿在工作中正常潤滑，減少磨損延長使用壽命。
③.不使用時應將防護套罩好。
4.當使用路面材料強度試驗儀電動操作試需要將搖把拔出取下
Note for pavement material strength tester:
1. The maximum limit position of the screw rod disc of the pavement material strength tester is 300mm from the top surface of the base box; the maximum limit position of the screw disc from the top surface of the base box is 60mm, If the above two limits are exceeded, the pavement material strength tester may be damaged.
2. The tester should be placed on a flat, stable location on the ground, and the tester should have grounding safety protection devices.
3. Pay attention to the maintenance of the road material strength tester:
①. The pavement material strength tester should always be kept clean and tidy. After each use, the table surface and surrounding environment must be cleaned and wiped clean.
②. After the screw rod and plate and column are wiped clean, anti-rust oil should be applied, and an appropriate amount of lubricant (No. 20 engine oil) should be dripped into the screw rod before use every day. In order to ensure the normal lubrication of the screw in the work, reduce wear and extend the service life.
③. Cover the protective cover when not in use.
4. When using the pavement material strength tester for electric operation test, it is necessary to pull out the handle
